This page describes the wfview transmit audio processor.
At this time, the transmit audio processor is only available for Network (Ethernet and WiFi) connected radios. We plan to make this feature available for USB-connected radios in the future.
The Transmit Audio Processor is designed to make the most of our voice audio over the limited bandwidth and noisy channel of ham radio communications. Similar to broadcast audio processors (Symetrix 528E, etc), this “chain” provides a noise gate, equalizer, and compressor.
When successfully adjusted, you will easily satisfy the demanding audio requirements of DX audio, or, at your discretion, obtain beautiful, almost “Hi-Fi” sounding audio. It’s completely up to you!
DX Audio:
- Uses just enough bandwidth (set this at your transmitter’s Transmit Bandwidth adjustments, typically 2.2k-2.7k)
- Sounds “Clear” — not “nasal” and not “boomy”
- Achieves 100% ALC with each syllable of speech, and yet, never sounds overdriven or splattery
- Does not sound like a loud leaf blower between words
Transmit Audio Chain
wfview’s transmit audio chain can take two forms:
Microphone –> Noise Gate –> Input Gain –> EQ –> Dyson Compressor –> Output Gain –> Radio
or
Microphone –> Noise Gate –> Input Gain –> Dyson Compressor –> EQ –> Output Gain –> Radio
It is generally better to do the EQ before the compressor, because any overly loud results from boosting are easily controlled with the Dyson Compressor. wfview’s audio path is 32 bits wide — a theoretical +130dB range — so do not worry about the effects of gaining up and down multiple times. You will never notice any difference in the fidelity, provided the final result does not exceed the headroom of the radio’s audio input.
For this to work successfully, you will need, at minimum, a basic PC headset with a microphone. Do not attempt this with a laptop’s build-in microphone, you will be disappointed (as will everyone you talk to on the air, and they will probably not hold back to tell you about it).
General Adjustment Procedure
Mic Gain
First, adjust the mic gain using your operating system’s Sound Control Panel. Most computer audio inputs have a control that sets the analog gain, and this is something you can usually adjust in the operating system’s control panels. So bypass the TX audio processor (check the “Master Bypass” checkbox), and turn on the TxAudio meter in wfview. Talk into the mic normally and then like you’re excited to work good DX, and adjust the level in your operating system’s Sound Control Panel. It’s a little different how you do this on each OS, so use google, you will easily find out how to do it. Adjust the level so that it never hits the full-scale value. Generally we want averages at -12dBfs and peaks around -6dBfs.
Now check the “Enable self-monitoring” checkbox at the bottom of the audio processor, and also enable “Mute RX Audio” so that you are not competing with stations you may hear on the air. If your audio is setup correctly, you should hear yourself in your headphones. Adjust the “Monitor Level” slider until you hear yourself comfortably loud. You may also need to turn up the volume control on in your operating system.
Noise Gate
The noise gate is your little assistant in muting the mic between words, which prevents background sounds (such as computer or amplifier fans) from being transmitted. The noise gate in wfview is extremely fast and does a good job at eliminating these annoying sounds.
Set these initial conditions:
- Attack: 5ms
- Hold: 10ms
- Decay: 10ms
- Range: -90 dB
- Key LF cut: 200 Hz
- Key HF cut: 2700 Hz
- Threshold: -70dB
Now begin speaking. You may hear the gate cut on and off between words. If you don’t hear this effect, move the threshold slider to the right a bit until you hear the background noise cut out. This will likely be somewhere between -70 and -55 dB, depending on how loud your environment is. When adjusted properly, normal speaking will come through just fine without any loss or false triggering.
Equalizer
This one is tricky to provide guidance for. But in general:
- Listen with enough loudness that you are not straining to hear yourself as you adjust. Listening too quietly tends to cause folks to boost everything up to the shape of their hearing loss!
- Adjust so that no one part of the spectrum dominates the sound. Ever hear someone that sounded “bassy” or “like they were on the telephone”? These are strong indications that their audio system was dominated by specific spectra. Boost only where you hear something lacking.
- Sometimes it helps to boost each slider up all the way and just listen to what that particular slider does, one at a time, and then go back and make gentle adjustments.
- Be mindful that most radios are going to cut off the transmit bandwidth hard around 2.7 KHz or earlier. So there is rarely any point to boost the last two sliders.
- In generally, boost no more than 3dB and cut no more than 6dB. This is just a rule of thumb, but generally too much of either will be “heard” as exactly that — an EQ someone jacked around without listening carefully.
- Watch the spectrum analyzer at the bottom. We generally compare the volume of the various “formants” of the voice. Hold a word long like “Auuuuddddiiioooo” and notice that there is a strong low frequency structure and also some higher frequency structures. A balanced sound will have nearly equal total volume of each side of the speech spectra. Not perfectly of course, but not wildly out of whack.
- Do not try and achieve “flat” spectra while speaking — this is probably not possible and does not reflect the sound you’re actually making with your mouth
- For DX audio, put in less low content. For rag chew, put in more 🙂
Dyson Compressor
The Dyson Compressor, named after its inventor, John S. Dyson (of FreeBSD fame), is an amazing compressor. Unlike a lot of compressors, the Dyson rarely makes any “pumping” artifacts and usually results in a very smooth yet loud sound. The Dyson Compressor has different parameters for Peaks and Average response. For ham radio, our typical radio compressors operate with incredibly high compression ratios. This is an important distinction compared with studio applications where we might use 4:1 or 6:1 for a person’s voice. For ham radio, you are seriously going to crank the ratio almost all the way up.
Adjustment Procedure:
Enable the Dyson Compressor.
Set the Input Gain to +10dB. We are going to be sure to hit the compressor with enough audio to work with.
Set the following controls:
- Threshold (formerly “Peak Limit”): -10dB
- Release time: 0.01s
- Fast ratio: 8:1
- Slow ratio: 8:1
With these settings, you should observe that each syllable of normal speech reaches 0dBfs (full volume). You may wish to set the Output gain control a bit lower or higher, hitting around -6dBfs on the output level, this way you can adjust the radio’s LAN gain for proper output with some output range for good adjustment.
Final Adjustment
Turn on TxAudio metering in wfview. Turn on ALC metering as well.
Use a dummy load and adjust the “LAN” slider in wfview until each syllable reaches 100% ALC. Never aim for more than 100% unless you have insight into how the radio works and can verify this is safe.
Use the “TX” slider in wfview to set the power output level desired. Never adjust the audio to hit a specific RF transmit level.
On SSB, you’ll probably notice much higher average output power, and that you are hitting peak output level very constantly. Be mindful of the increased duty cycle that this places on all your equipment.

